Post-lunch nap as a worksite intervention to promote alertness on the job.

A worksite study was conducted to examine whether a 15-min nap during a post-lunch rest period would affect subsequent alertness, performance, and nocturnal sleep in eight factory workers under a 3-week protocol. Subjects were asked to take the nap at 12:30 h on a reclining chair during the nap week, and to remain awake during the no-nap week. The order of these 2 weeks was counterbalanced between the subjects. During the third, follow-up week, each subject determined whether or not she/he would nap. Alertness on the job and nocturnal sleep were assessed using a sleep diary. Wrist activity was also recorded during sleep at night. Choice reaction time task (RT) was performed at 10:00 and 15:00 h every day of the nap week and every other day of the no-nap and follow-up weeks. Perceived alertness was significantly higher in the afternoon after nap than after no nap at the end of the week. Similar effects were observed during the follow-up week where almost half of the subjects napped. No significant differences between the three weeks were found for RT performance or nocturnal sleep. Workers' attitudes toward the nap were favourable. Although further intervention research is required, our results suggest that post-lunch napping may have the potential to promote daytime alertness at work.     

Acquisition-time estimation for over 10 Gbit/s clock and data recovery ICs

A method to estimate the acquisition time for the clock and data recovery (CDR) IC using the linear phase-locked loop (PLL) technique is proposed. Estimations using the method follow the measured acquisition time for the PLL with any loop parameters, which makes it possible to design the CDR IC for various targets.     

Phenol novolac/poly(4- hydroxyphenylmaleimide) blend hardeners for DGEBA-type epoxy resin

Phenol novolac/poly (4-hydroxyphenylmaleimide) (PHPMI) blends were used as an epoxy resin hardener. The curing behavior of the above system and the thermal and mechanical properties of the cured epoxy resin were studied. It was not necessary to use a curing accelerator for this system, because PHPMI caused acceleration of the curing reaction. The curing mechanism of this system was investigated by using model compounds. Test pieces from the neat resins and the glass fiber reinforced resins were evaluated in terms of thermal and mechanical properties, respectively. It was found that heat resistance and mechanical properties were improved by increasing the amount of PHPMI in the hardener.     

Hydrothermal upgrading of wood biomass: Influence of the addition of K2CO3 and cellulose/lignin ratio

The hydrothermal treatment of two different wood biomass samples such as cherry (hard wood) and cypress (soft wood), whose composition is different i.e. lignin, cellulose and hemicellulose were performed at 280 °C for 15 min with aq. K₂CO₃ with different concentrations (0–1 M). The soft wood biomass contains higher lignin content than hard wood biomass. The cellulose rich cherry wood biomass produced higher proportion of acetic acid than cypress. The lignin rich cypress produced the hydrocarbons with major portion of phenolic hydrocarbons and derivatives than cherry. The total oil yields from both cherry and cypress wood biomass produced 50 wt% of liquid hydrocarbons at 280 °C for 15 min with 0.5 M K₂CO₃ solution. The volatility distribution of liquid hydrocarbons showed the characteristic features of soft and hard wood biomasses.     

1-O-alkyl-2,3-diacylglycerols in the skin surface lipids of the hairless mouse

A neutral lipid class was isolated by thin-layer chromatography from the skin surface lipids of the hairless mouse. The fraction migrated faster than triglycerides and had a migration rate similar to that of diacyl alkanediols (diester wax). Upon deacylation, however, the long-chain diols were identified as 1-alkylglycerol ethers based on their chromatographic properties and on the mass spectra of their nicotinylidene derivatives. Thus, the skin lipid fraction was identified as 1-O-alkyl-diacylglycerol. The alkyl moieties were all saturated and even-numbered and ranged in chainlength from C₁₆ to C₂₂ with 1-O-hexadecylglycerol amounting to 34% of the total glycerol ether moieties. The fatty acids derived from this lipid fraction were mostly monoenoic with chainlengths ranging from C₁₆ to C₂₄. The major acyl component was eicosenoic acid (20∶1) representing 61% of the total fatty acids.     

New type of tin support for hydroprocessing catalyst

TiN supported molybdenum sulfide catalysts showed much higher activity for cleavage of C-C bonds than oxide supported molybdenum sulfide catalysts, indicating the possibility of a new generation of supports for hydroprocessing catalysts.     

A novel architecture of dynamically reconfigurable fused multiply–adder for digital signal processing

Introduction

Multiply-accumulate operation is the most fundamental operation in digital signal processing for image processing, robotics and automatic control. In this paper, a novel architecture of dynamically reconfigurable fused multiply-adder (FMA) is proposed.

Methods

Dynamic reconfiguration is a method that can change the circuit configuration without stop of operation. The proposed circuit provides the following four calculation modes by dynamic reconfiguration: (1) complex number FMA mode, (2) real number FMA mode, (3) complex number parallel calculation mode, and (4) real number parallel calculation mode.  The data format is single precision floating point format based on IEEE754. The proposed circuit was designed using Verilog-HDL. It was simulated by logic circuit simulator, and implemented on FPGA.

Result

As a result of circuit synthesis, we confirmed the reduction of resource in the proposed circuit. Furthermore, we confirmed proper result for each calculation mode by logic simulation and experiment on FPGA.

Conclusion

The proposed circuit provides the four calculation modes by dynamic reconfiguration. We confirmed the reduction of resource and proper result for each calculation mode.     

Structure and viscoelastic properties of epoxy resins prepared from four-nuclei novolacs

The relation between the structure and the viscoelastic properties of seven kinds of epoxy resins was studied. Seven tetraglycidylethers were synthesized from four-nuclei novolacs in which the positions of methylene linkage or number of kind of substituents were different. These epoxy compounds were cured with diaminodiphenylmethane as a hardener. From the viscoelastic properties of the fully cured resins with the hardener, characteristic properties such as glass transition temperature (T_g), average molecular weight between crosslinking points (M̄_c), and front factor (ϕ) were obtained. It was concluded that higher linearity in the main chain of epoxy resins gave a cured resin with a higher T_g, a smaller M̄_c, and a larger ϕ.